Грунд за Циментови Хидроизолации CRYLADIT
Cryladit
Prepared from modified acrylic polymers designed for use as an additive in mixing Portland cement mortars, improving the strength and adhesion properties of surfaces made from concrete, brick, stone, etc.
Construction solutions prepared with CRYLADIT can be used internally and externally, offering strength and fast settling.
- Опаковки — 10 литра · 5 литра
- Colours — Бял
Технически лист
ВСИЧКО ЗА CRYLADIT
Пълната информация от техническата спецификация на производителя — приложение, подготовка на основата, употреба и технически данни.
Технически лист и документи
Description
CRYLADIT is a milky white liquid with a density slightly above that of water, 1.06 kg/dm3which can be mixed pure or diluted with water.
Preparation
Pre-clean the surface to be treated and, if necessary, remove any excess material and moisture from the surface without causing water build-up.
Sand and cement must be mixed separately and also with CRYLADIT with water in the recommended proportion. Then prepare the table.
If it is necessary to use a trowel, do not do it immediately, but wait 15-20 min. Never squeeze the trowel as this will cause the polymers to come to the surface and the behaviour will not be the same.
References
When settling is too rapid due to high temperatures, we recommend using wet bags to cover the treated surface or spraying the surface with TECMA HMF thus avoiding dehydration of the surface of the treated area. At low temperatures below +50C is not recommended to apply the mixture.
Packaging
In 25 and 60 litre disposable plastic containers.
Dosage
| Application: | Dosage: |
| Drying of concrete and cracks | Only pure CRYLADIT |
| Concrete coatings over 7 cm | 2:1 two parts CRYLADIT and a water |
| As a grip additive for TECMADRY | 5 L water and 1.5-2 L CRYLADIT per bag |
| Construction mortars with adhesion and plasters requiring crack reduction | 1:3 one part CRYLADIT and three parts water |
These proportions are for normal conditions.
When traction is more critical, the amount of CRYLADIT should be increased. In case of doubt, we recommend that you take a test.
Грунд за Циментови Хидроизолации
ПРИЛОЖЕН НА РЕАЛНИ ОБЕКТИ ОТ НАШИТЕ БРИГАДИ
Продуктът е част от системи, които сами проектираме и полагаме. Вижте как работи на място — и ни разкажете за вашия обект.
НЕ СТЕ СИГУРНИ ДАЛИ ТОВА Е ПРАВИЛНИЯТ ПРОДУКТ?
Опишете ни обекта — нашите техници ще потвърдят продукта, разходната норма и начина на полагане, безплатно и обикновено до 1 работен ден.
Още продукти от категория „Грундове“ — подбрани така, че да работят заедно в една система: подготовка, полагане и защита с материали от един производител.
Primer for Polyurethane Sealants - PRIMER 1833
Reinforcement primer for rust surfaces - SATECMACONS AAJ
Epoxy Primer Suitable for Wet Surfaces - TECMA PAINT AH - 5 kg.
Bonding Material Between Different Surfaces - TECMA ADH
Primer for Silicate Paints - TECMASIL PRIMER
Product of Bitumen Emulsion with Latex - TECMA PAINT BITUM CAUCHO
Treatment of Porous Surfaces - IMPRIMACION A
Acrylic Primer for Wet Surface
Anticorrosion Primer - TECMA PAINT OX
Иновативните и висококачествени решения
СВЪРЖЕТЕ СЕ С НАС
Търсите надеждно и естетично решение за вашия обект? Обадете ни се още днес — ще изготвим безплатна консултация и оферта, съобразена с вашите конкретни изисквания.