Епоксиден Грунд Подходящ и за Влажни Повърхности TECMA PAINT AH
Tecma Paint A-H
Solvent-free epoxy primer specially formulated for application on wet or dry mineral substrates, with excellent adhesion and sealing ability on substrates such as mortar, concrete, tile, natural and artificial stone, plaster, etc.
- Опаковки — 5 килограма
- Colours — Прозрачен
Технически лист
ВСИЧКО ЗА TECMA PAINT AH
Пълната информация от техническата спецификация на производителя — приложение, подготовка на основата, употреба и технически данни.
Технически лист и документи
Annex
TECMA PAINT A-H used as a bridge over any type of wet surfaces that will be coated with epoxy or polyurethane resins such as TECMA PAINT ECOPOX, TECMA IMPERAL P-2008, TECMA PAINT EP-SD, TECMA PAINT AUTONIVELANTE. Its excellent sealing properties allow it to be used as a bridge between different coatings and surfaces where bonding difficulties would arise.
Preparation
Surfaces must be dry and free of grease, oil, sand, dust and any other contaminant. The substrate must be solid and free of loose particles. If you are laying on very smooth surfaces, we recommend first blasting mechanically or chemically with DESCA 2F to be able to achieve some porosity and roughness of the base.
Usage
Pour the container with the Hardener into the container with the Base and mix for about 2 min. until a homogeneous mixture is obtained. Apply with a brush, roller or rubber mallet covering the entire surface. After a minimum of 8 h, you can apply the finishing coat.
References
- Do not apply at temperatures below +50С
- Do not prepare more solution than you could use during its open run time.
Packaging
The product is supplied in metal boxes of 3 kg Base and 2 kg Hardener.
In tightly closed containers, the product can be stored for 1 year at temperatures up to +300С.
Our information and recommendations should be interpreted without legal obligation. It is the customer's responsibility to verify the suitability of the products for their intended purposes.
Technical Data
| Type | Epoxy resin |
| Ratio between base and hardener | 6/4 |
| Open operating time at +230С | 45 min. |
| Laying | Brush, roller, rubber malamaska |
| Cost rate | 6 m2/kg per 150 µm |
| Appearance | Satin |
| Drying time | Touch : 6 h Hard : 12 h Repainting : 8 h minimum, 48 h maximum |
Епоксиден Грунд Подходящ и за Влажни Повърхности
ПРИЛОЖЕН НА РЕАЛНИ ОБЕКТИ ОТ НАШИТЕ БРИГАДИ
Продуктът е част от системи, които сами проектираме и полагаме. Вижте как работи на място — и ни разкажете за вашия обект.
НЕ СТЕ СИГУРНИ ДАЛИ ТОВА Е ПРАВИЛНИЯТ ПРОДУКТ?
Опишете ни обекта — нашите техници ще потвърдят продукта, разходната норма и начина на полагане, безплатно и обикновено до 1 работен ден.
Още продукти от категория „Грундове“ — подбрани така, че да работят заедно в една система: подготовка, полагане и защита с материали от един производител.
Acrylic Primer for Wet Surface
Anticorrosion Primer - TECMA PAINT OX
Primer for Polyurethane Sealants - PRIMER 1833
Primer for Cement Waterproofing - CRYLADIT
Primer for Silicate Paints - TECMASIL PRIMER
Bonding Material Between Different Surfaces - TECMA ADH
Treatment of Porous Surfaces - IMPRIMACION A
Reinforcement primer for rust surfaces - SATECMACONS AAJ
Product of Bitumen Emulsion with Latex - TECMA PAINT BITUM CAUCHO
Иновативните и висококачествени решения
СВЪРЖЕТЕ СЕ С НАС
Търсите надеждно и естетично решение за вашия обект? Обадете ни се още днес — ще изготвим безплатна консултация и оферта, съобразена с вашите конкретни изисквания.