Акрилен Грунд за Влажни Повърхност TECMA BASS SH
A special primer for surfaces with a high degree of moisture, making it impossible to apply any other paint. Thanks to its components that react with water, bonding is ensured on damp surfaces, forming a layer that is firmly fixed to the substrate.
When the coating is dry, it prevents the passage of moisture from the substrate, thus allowing the subsequent application of water-based or solvent-based paints that are compatible with TECMA BASS SH.
- Опаковки — 12 килограма · 6 килограма
- Colours — Бял
Технически лист
ВСИЧКО ЗА TECMA BASS SH
Пълната информация от техническата спецификация на производителя — приложение, подготовка на основата, употреба и технически данни.
Технически лист и документи
Annex
The use of TECMA BASS SH is recommended for surfaces that are permanently or temporarily wet and then acrylic waterproofing or vinyl paints (plastic paints) will be applied. It is suitable for both indoor and outdoor use.
It can be applied on any mineral base used in construction : bricks, masonry, tiles, concrete, etc.
TECMA BASS SH is used as a primer for some of our waterproofing coatings TECMA ELAST V-97, IMPERMEABILIZANTE E-88, TECMA PAINT FACHADAS и TECMA PAINT AS.
Preparation
The surface must be clean, dry and free of oil, grease, dirt, soil or any other contaminant.
Method of application:
- Stir TECMA BASS SH before you lay it down.
- Once the substrate is prepared, apply the first coat of product over the entire surface. Your consumption should vary from 150 - 250 gr/m2 in 1 or 2 layers, depending on the humidity and porosity of the substrate.
- After 8 h, you can apply the waterproofing or finish paint.
References
- Do not apply at temperatures below +50C or relative humidity higher than 95%
- When laying in very high relative humidity or when the substrate is extremely wet, the drying time may be longer
Packaging
TECMA BASS SH is supplied in 7 and 14 kg metal boxes. The product must be stored in a frost-free place, so its shelf life is 1 year.
Our information and recommendations should be interpreted without legal obligation. It is the customer's responsibility to verify the suitability of the products for their intended purposes.
Technical Data
| Density at +200С | 1,4 ± 0,05 gr/cm3 |
| Viscosity at +250С | 110 ± 5 KU |
| Appearance | Thixotropic, white colour |
| Application | With brush or roller |
| Drying time at 200C and 55% O.V | Touch - 2 h Fully - 6 h Repainting - 8 h |
| Cost rate | 150 - 250 gr/m2 depending on the substrate humidity |
| Bonding to wet substrate | Clay slabs : 21,9 kg/cm2 Horosan : 22.6 kg/cm2 Solid brick : 11,7 kg/cm2 |
Акрилен Грунд за Влажни Повърхност
ОБЕКТИ, ИЗПЪЛНЕНИ СЪС СИСТЕМИТЕ НА SATECMA
Проектираме, доставяме и полагаме със собствени бригади — с писмена гаранция за изпълнението. Разкажете ни за вашия обект.
НЕ СТЕ СИГУРНИ ДАЛИ ТОВА Е ПРАВИЛНИЯТ ПРОДУКТ?
Опишете ни обекта — нашите техници ще потвърдят продукта, разходната норма и начина на полагане, безплатно и обикновено до 1 работен ден.
Още продукти от категория „Грундове“ — подбрани така, че да работят заедно в една система: подготовка, полагане и защита с материали от един производител.
Reinforcement primer for rust surfaces - SATECMACONS AAJ
Primer for Cement Waterproofing - CRYLADIT
Primer for Polyurethane Sealants - PRIMER 1833
Primer for Silicate Paints - TECMASIL PRIMER
Anticorrosion Primer - TECMA PAINT OX
Epoxy Primer Suitable for Wet Surfaces - TECMA PAINT AH - 5 kg.
Bonding Material Between Different Surfaces - TECMA ADH
Product of Bitumen Emulsion with Latex - TECMA PAINT BITUM CAUCHO
Treatment of Porous Surfaces - IMPRIMACION A
Иновативните и висококачествени решения
СВЪРЖЕТЕ СЕ С НАС
Търсите надеждно и естетично решение за вашия обект? Обадете ни се още днес — ще изготвим безплатна консултация и оферта, съобразена с вашите конкретни изисквания.