Бързо Стягащ Строителен Разтвор за Ремонт на Бетон PREMHOR R

PREMHOR-R поради факта, че се сляга и се втвърдява много бързо, е съществен при ремонт и възстановяване на бетон през зимата (замазване на бетон, ремонт на навеси, подпрозоречни дъски, щурцове и сачаци, съединенията между стените и между стените и пода, ремонт на кухини, вдлъбнатини и пукнатини, ремонт на бетон в подове, мостове, тунели, язовири, цистерни и водни резервоари и др.). В допълнение, PREMHOR-R също силно се препоръчва и за бързо укрепване, когато продукта трябва да слегне и да се втвърди бързо.

Accreditations

CE marking as conforming to EN 1504-2 (system 2+) and the European Construction Products Regulations.

Surface preparation

The surface must be hard (with a tensile strength of more than 1 N/mm2) and clean, free from grease, oil, paint, residue, mortar, loose material, sand, dust or any other contaminant. We recommend that the surface be properly prepared, preferably by mechanical means (sandblasting, intensive brushing, etc.). Surfaces that are very smooth and/or slightly porous should be treated in the same way, preferably mechanically, so that they become sufficiently rough and porous. When repairing imperfections and patches, the surface should be cleaned beforehand and any loose material removed, if necessary using a chisel prepare the edges of the area to be treated to be beveled and vertical.

При ремонт на пукнатини или фисури, ги отворете съответно по тяхната ширина, дължина и дълбочина, така че да се получат вертикални разрези. Оставете напречни сечения и измийте повърхността, която ще бъде третирана с вода.

When repairing concrete surfaces that have suffered surface damage, brush them intensively with a wire brush until the surface is stable and free of any fragments. Then wash the area with water. If you need to repair concrete areas where reinforcement is visible, sandblast them and then apply TECMA PAINT OXto protect the fittings.

Soak highly absorbent surfaces with water - avoiding mixing - and then wait until the surface takes on a matt appearance before applying the product.

Construction Solution for Adhesion

Before applying PREMHOR-R we recommend to apply a mortar for adhesion obtained from PREMHOR-R and approximately 30% of water. Use a brush to apply it to the entire surface to be repaired and note that you must apply PREMHOR-R към повърхността докато строителния разтвор все още не е изсъхнал – разполагате с приблизително 5 min.

Instructions

PREMHOR-R should be mixed with clean water and stirred until it becomes a homogeneous, lump-free paste. We recommend mixing one bag with PREMHOR-R  с 3,75 – 4,25 l вода. Не добавяйте повече вода от препоръчителното.

Веднъж след като сместа е готова, нанесете продукта незабавно. След като сте приготвили сместта, не трябва да са минали повече от 5-10 min. преди да я нанесете.

To make sure the adhesion mortar stays fresh, do not mix any more PREMHOR-Rthan can be used within the durability after mixing the paste.

Application

The paste obtained from PREMHOR-R  and water should be applied to sections that need repair. Use a trowel to fill voids, blemishes, patches, cracks, etc. Once you have spread the paste, wet the trowel and use it to smooth.

You should not try to apply a layer of PREMHOR-R exceeding 2 cm each time. Apply several coats if you need a thicker layer.

Once you have applied PREMHOR-R make sure it is kept wet by spraying it with water over the next 8 h.

Special Applications

To strengthen and increase adhesion to certain surfaces, PREMHOR-R may be mixed with a solution of two parts water and one part CRYLADIT. For a bag of PREMHOR-R ще са нужни приблизително 2,50 l вода и 1,50 l CRYLADIT. First of all, mix the water with CRYLADIT and then add this mixture to PREMHOR-R. You can also use this mixture of water and CRYLADIT in the mortar for adhesion.

Where the high degree of adhesion is due to the special nature of the application (repairing surfaces subject to heavy and intense traffic or structural concrete, etc.), we recommend applying primer to the surface when it is completely dry - use products such as TECMA PAINT AD or TECMA PAINT R and then apply PREMHOR-R while the primer is still dry.

Специални Прeпоръки

• To apply the product correctly, do not mix more PREMHOR-Rthan necessary. Pay attention to the suitability after mixing the paste and make sure that the mortar for adhesion is fresh.
• Do not add any material to the product other than those specifically required for the mixture.
• Do not apply when the temperature drops below +5⁰C or if freezing is expected in the next 24 h
• Do not apply to frozen or frozen surfaces
• Moisten the surface before application PREMHOR-R
• Make sure that when you apply PREMHOR-R it is kept wet for the next 8 h, in particular in warm weather. Spray with TECMA-HMF to prevent dehydration.
• Do not apply a single coat that is thicker than 2 cm.
• Do not add more water to the mortar than the specified amount

PREMHOR-R is delivered in 25 kg. mesh paper bags. PREMHOR-R must be stored sealed in the original bags. The expected shelf life in the original bags should not exceed 12 months.

Our information and recommendations should be interpreted without legal obligation. It is the customer's responsibility to verify the suitability of the products for their intended purposes.